| Effect of Asymmetric Geometry on the Flexibility of Stent A Syaifudin, R Takeda, K Sasaki JMES The International Journal of Mechanical Engineering and Sciences 1 (1), 1-7, 2017 | 9 | 2017 |
| Studies of the effect of melt spinning on the electrochemical properties of the AB2 Laves phase alloys ID Wijayanti, L Mølmen, RV Denys, MN Guzik, S Gorsse, JL Bobet, ... JMES The International Journal of Mechanical Engineering and Sciences 5 (1), 2021 | 7 | 2021 |
| Numerical study of blended winglet geometry variations on unmanned aerial vehicle aerodynamic performance FD Pertiwi, A Wahjudi JMES The International Journal of Mechanical Engineering and Sciences 6 (1 …, 2022 | 4 | 2022 |
| Numerical study of bach-bladed savonius wind turbine with varying blade shape factor K Ibrahim, VS Djanali, N Ikhwan JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 4 | 2020 |
| Design and analysis of ECVT on electric powered vehicles for determining the speed ratio HS Maulana, IN Sutantra JMES The International Journal of Mechanical Engineering and Sciences 5 (2 …, 2021 | 3 | 2021 |
| Numerical study effect of fluidizing air to erosion pattern in circulating fluidized bed boiler B Sudarmanta JMES The International Journal of Mechanical Engineering and Sciences 1 (2 …, 2017 | 3 | 2017 |
| Effect of Fluctuating Load on Fatigue of PPCW Flat Wagon T Suprianto, A Syaifudin, LW Pamungkas, JB Ariatedja, AR Farid JMES The International Journal of Mechanical Engineering and Sciences 7 (1 …, 2023 | 2 | 2023 |
| Numerical Study of Deflection and Stress Distribution on Composite Box Spar Structure–Application In Wind Turbine Blade PS Ufaira, P Suwarta, G Bangga JMES The International Journal of Mechanical Engineering and Sciences 6 (1 …, 2022 | 2 | 2022 |
| Numerical study of epoxy-ramie fiber composite as a type iv ballistic resistant material S Sutikno, RF Rizal, A Safaat JMES The International Journal of Mechanical Engineering and Sciences 5 (1 …, 2021 | 2 | 2021 |
| Design of a Patient Wrist Rehabilitation Device with Servo Motor Drive LY Amali, IML Batan JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 2 | 2020 |
| Failure analysis of superheater tubes made from material T91 in the boiler of a 600 MW power plant KA Munif JMES The International Journal of Mechanical Engineering and Sciences 4 (1 …, 2020 | 2 | 2020 |
| Experimental Study of the Effect of Magnetization on Bioethanol Injectors on Spray Characteristics for Applications in the SINJAI-150 Engine IBS Amalia Dwi Utami, Bambang Sudarmanta, Budi Utomo Kukuh Widodo, Ary ... JMES The International Journal of Mechanical Engineering and Sciences 3 (no …, 2019 | 2* | 2019 |
| The Influence Of Sand Casting Mold Solidfication Pressure Variations To The Quality Of Al-Si Alloy Casting Product A Fajri, B Basyirun JMES The International Journal of Mechanical Engineering and Sciences 2 (2 …, 2018 | 2 | 2018 |
| Experimental Study on Effect of Injection Pressure to Spray Characteristics, Performance and Emissions of DieselEngine DI 20 C Using Biodiesel Fuel AAK Mahanggi, B Sudarmanta, H Soebagyo JMES The International Journal of Mechanical Engineering and Sciences 2 (1 …, 2018 | 2 | 2018 |
| Dynamic Analysis of Narrow Tilting Three Wheeled Vehicle (NTTWV) with LQG control MF Adhim, U Wasiwitono JMES The International Journal of Mechanical Engineering and Sciences 1 (2 …, 2017 | 2 | 2017 |
| Failure Analysis of Bend Tube Preheater on Heat Recovery Steam Generator RSE Putro, A Hariyadi, S Suwarno JMES The International Journal of Mechanical Engineering and Sciences 1 (1 …, 2017 | 2 | 2017 |
| Numerical study of heat transfer characteristics in high pressure steam turbine during stop unit process with sliding pressure B Santoso, BA Dwiyantoro JMES The International Journal of Mechanical Engineering and Sciences 6 (2 …, 2022 | 1 | 2022 |
| Engine rpm and battery soc activation optimization in hybrid vehicle energy management system utilizing bpnn-genetic algorithm and bpnn–particle swarm optimization RAM Wicaksana, B Sudarmanta, MK Effendi JMES The International Journal of Mechanical Engineering and Sciences 6 (2 …, 2022 | 1 | 2022 |
| Effect of Diffusers Installation in Inlet Primary Air Coal Pulverizer on Airflow Characteristic and Wear Concentration using CFD Modeling RPSW Galih, BA Dwiyantoro JMES The International Journal of Mechanical Engineering and Sciences 6 (2 …, 2022 | 1 | 2022 |
| Numerical Analysis on Flexibility of Unexpanded Balloon-Expandable Stent IA Aribowo, VJN Susanto JMES The International Journal of Mechanical Engineering and Sciences 6 (1), 1-8, 2022 | 1 | 2022 |
