Follow
Akhyar
Title
Cited by
Cited by
Year
Magnetic behavior of natural magnetite (Fe3O4) extracted from beach sand obtained by mechanical alloying method
Z Jalil, A Rahwanto, Mustanir, H Akhyar, E Handoko
AIP Conference Proceedings 1862 (1), 030023, 2017
282017
Study on Cooling Curve Behavior During Solidification and Investigation of Impact Strength and Hardness of Recycled Al–Zn Aluminum Alloy
H Akhyar, Husaini
International Journal of Metalcasting 10 (4), 452-456, 2016
202016
Hot tearing susceptibility of aluminum alloys using CRCM-Horizontal mold
H Akhyar, V Malau, PT Iswanto
Results in physics 7, 1030-1039, 2017
162017
Non Treatment, T4 and T6 on Tensile Strength of Al-5.9Cu-1.9Mg Alloy Investigated by Variation of Casting Temperature
A Hasan, PT Iswanto, V Malau
Materials Science Forum 929, 56-62, 2018
152018
Community collection of ocean current data: An example from Northern Aceh Province, Indonesia
S Rizal, HA Haridhi, CR Wilson, H Akhyar, I Setiawan, SCH Cheung, ...
SPC Traditional Marine Resource Management and Knowledge Information …, 2013
152013
Desorption properties of mechanically milled MgH2 with double catalysts Ni and SiC
A Rahwanto, Z Jalil, Akhyar, E Handoko
IOP Conference Series: Materials Science and Engineering 931 (1), 012012, 2020
142020
Structural Simulations of Bicycle Frame Behaviour under Various Load Conditions
Akhyar, Husaini, H Iskandar, F Ahmad
Materials Science Forum 961, 137-147, 2019
132019
MgH2-SiC based hydrogen storage material prepared by reactive mechanical alloying method
Z Jalil, A Rahwanto, H Akhyar, R Razali, E Handoko
IOP Conference Series: Earth and Environmental Science 105 (1), 012098, 2018
132018
Experiment on Hardness and Impact Strength of Recycled Aluminum Alloys by Metal Casting Process
F Ahmad, Akhyar, A Masri
Materials Science Forum 961, 65-72, 2019
122019
Effect of shot peening at different almen intensities on fatigue behavior of AISI 304
PT Iswanto, H Akhyar, FF Utomo
Metalurgija 57 (4), 295-298, 2018
112018
Analysis of tsunami disaster map by geographic information system (GIS): Aceh Singkil-Indonesia
A Farhan, H Akhyar
IOP conference series: earth and environmental science 56 (1), 012002, 2017
112017
Perancangan dan Pembuatan Dapur Peleburan Logam dengan Menggunakan Bahan Bakar Gas (LPG)
AZ Mubarak, H Akhyar
Jurnal Teknik Mesin Unsyiah 1 (3), 128-132, 2013
112013
MODIFICATION OF CONSTRAINED ROD CASTING MOLD FOR NEW HOT TEARING MEASUREMENT
V Malau, Akhyar, PT Iswanto
Archives of Metallurgy and Materials 63 (3), 1201-1208, 2018
102018
Fatigue crack growth rate of motorcycle wheel fabricated by centrifugal casting
PT Iswanto, Akhyar, EUK Maliwemu
Metalurgija 58 (1-2), 51-54, 2019
92019
Hydrogen storage properties of mechanical milled MgH2-nano Ni for solid hydrogen storage material
Z Jalil, A Rahwanto, E Handoko, H Akhyar
IOP Conference Series: Materials Science and Engineering 432 (1), 012034, 2018
92018
Effect of Different Gating Systems and Sand Mold Binder on the Cast-Quality of Bicycle Frame Produced through Sand Casting Method
Akhyar, Husaini, M Ali, N Ali, F Ahmad
Defect and Diffusion Forum 402, 100-107, 2020
72020
Effect of T6 heat treatment and artificial aging on mechanics and fatigue properties of A356. 0 aluminum alloy produced by 350 rpm centrifugal casting
PT Iswanto, H Akhyar, V Malau, R Wirawan
2016 6th International Annual Engineering Seminar (InAES), 223-227, 2016
72016
Effect of shot peening on microstructure, hardness, and corrosion resistance of AISI 316L
PT Iswanto, H Akhyar, A Faqihudin
Journal of Achievements in materials and manufacturing Engineering 89 (1), 2018
62018
Experimental investigation on open sun-drying and solar drying system of bilimbi
D Harun, MI Maulana, H Akhyar
2016 6th International Annual Engineering Seminar (InAES), 271-275, 2016
62016
Effect Pouring Temperature on Casting Defect Susceptibility of Hot Tearing in Metal Alloy Al-Si
H Akhyar, Suyitno
Applied Mechanics and Materials 758, 95-99, 2015
62015
The system can't perform the operation now. Try again later.
Articles 1–20